CISCO CCNA Exam – Q292

Which command can you enter to configure a local username with an encrypted password and EXEC mode user privileges?

A. Router(config)#username jdone privilege 1 password 7 08314D5D1A48
B. Router(config)#username jdone privilege 1 password 7 PASSWORD1
C. Router(config)#username jdone privilege 15 password 0 08314D5D1A48
D. Router(config)#username jdone privilege 15 password 0 PASSWORD1

Correct Answer: A

CISCO CCNA Exam – Q291

Which three commands can you use to set a router boot image? (Choose three.)

A. Router(config)# boot system flash c4500-p-mz.121-20.bin
B. Router(config)# boot system tftp c7300-js-mz.122-33.SB8a.bin
C. Router(config)#boot system rom c7301-advipservicesk9-mz.124-24.T4.bin
D. Router> boot flash:c180x-adventerprisek9-mz-124-6T.bin
E. Router(config)#boot flash:c180x-adventerprisek9-mz-124-6T.bin
F. Router(config)#boot bootldr bootflash:c4500-jk9s-mz.122-23f.bin

Correct Answers: A, B, C

CISCO CCNA Exam – Q290

Which three statements about static routing are true? (Choose three.)

A. It uses consistent route determination.
B. It is best used for small-scale deployments.
C. Routing is disrupted when links fail.
D. It requires more resources than other routing methods.
E. It is best used for large-scale deployments.
F. Routers can use update messages to reroute when links fail.

Correct Answers: A, B, C

CISCO CCNA Exam – Q288

Which command can you enter to display the hits counter for NAT traffic?

A. show ip nat statistics
B. debug ip nat
C. show ip debug nat
D. clear ip nat statistics

Correct Answer: A

CISCO CCNA Exam – Q286

Refer to the exhibit.
CISCO CCNA Exam – Q286

The following commands are executed on interface fa0/1 of 2950Switch.
2950Switch(config-if)# switchport port-security
2950Switch(config-if)# switchport port-security mac-address sticky
2950Switch(config-if)# switchport port-security maximum 1
The Ethernet frame that is shown arrives on interface fa0/1. What two functions will occur when this frame is received by 2950Switch? (Choose two.)

A. The MAC address table will now have an additional entry of fa0/1 FFFF.FFFF.FFFF.
B. Only host A will be allowed to transmit frames on fa0/1.
C. This frame will be discarded when it is received by 2950Switch.
D. All frames arriving on 2950Switch with a destination of 0000.00aa.aaaa will be forwarded out fa0/1.
E. Hosts B and C may forward frames out fa0/1 but frames arriving from other switches will not be forwarded out fa0/1.
F. Only frames from source 0000.00bb.bbbb, the first learned MAC address of 2950Switch, will be forwarded out fa0/1.

Correct Answers: B,D

Explanation:
The configuration shown here is an example of port security, specifically port security using sticky addresses. You can use port security with dynamically learned and static MAC addresses to restrict a port’s ingress traffic by limiting the MAC addresses that are allowed to send traffic into the port. When you assign secure MAC addresses to a secure port, the port does not forward ingress traffic that has source addresses outside the group of defined addresses. If you limit the number of secure MAC addresses to one and assign a single secure MAC address, the device attached to that port has the full bandwidth of the port.
Port security with sticky MAC addresses provides many of the same benefits as port security with static MAC addresses, but sticky MAC addresses can be learned dynamically.
Port security with sticky MAC addresses retains dynamically learned MAC addresses during a link-down condition.

CISCO CCNA Exam – Q285

What will be the result if the following configuration commands are implemented on a Cisco switch?

Switch(config-if)# switchport port-security
Switch(config-if)# switchport port-security mac-address sticky

A. A dynamically learned MAC address is saved in the startup-configuration file.
B. A dynamically learned MAC address is saved in the running-configuration file.
C. A dynamically learned MAC address is saved in the VLAN database.
D. Statically configured MAC addresses are saved in the startup-configuration file if frames from that address are received.
E. Statically configured MAC addresses are saved in the running-configuration file if frames from that address are received.

Correct Answer: B

Explanation:
In the interface configuration mode, the command switchport port-security mac-address sticky enables sticky learning. When entering this command, the interface converts all the dynamic secure MAC addresses to sticky secure MAC addresses.

CISCO CCNA Exam – Q284

Drag each category on the left to its corresponding router output line on the right. Each router output line is the result of a show ip interface command. Not all categories are used.
Select and Place:
CISCO CCNA Exam – Q284

CISCO CCNA Exam – Q284b

Explanation:
A simple way to find out which layer is having problem is to remember this rule: “the first statement is for Layer 1, the last statement is for Layer 2 and if Layer 1 is down then surely Layer 2 will be down too”, so you have to check Layer 1 before checking Layer 2. For example, from the output “Serial0/1 is up, line protocol is down” we know that it is a
layer 2 problem because the first statement (Serial0/1 is up) is good while the last statement (line protocol is down) is bad. For the statement “Serial0/1 is down, line protocol is down”, both layers are down so the problem belongs to Layer 1.
There is only one special case with the statement “…. is administrator down, line protocol is down”. In this case, we know that the port is currently disabled and shut down by the administrators.